87130A ATTENUATOR SWITCH DRIVER

0 Comments

Warranty service for products installed by Agilent Technologies and certain other products designated by Agilent Technologies will be performed at Buyer s facility at no charge within Agilent Technologies service travel areas. To the extent permitted by local law, this warranty applies only to branded Agilent Technologies products and not to products manufacture by others that may be sold or distributed by Agilent Technologies. Refer to the section Example Speed Calculation on page for an explanation on calculating and minimizing overall switching time. Addresses 0 and 31 are typically reserved for GPIB functions and should not be used. Special longer lengths of heavier-gauge driver 68 pin and CPU 36 pin cables are available.

Uploader: Kishakar
Date Added: 5 January 2004
File Size: 15.78 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 17286
Price: Free* [*Free Regsitration Required]

These low impedance pulses can be adjusted for pulse width in order to optimize switching speed. Addresses 0 and 31 are typically reserved for GPIB functions and should not be used. Use this software only with the A.

On card 1, J1 to J31 correspond to channels to on your switch driver channel menu. S1 wsitch is open or away from the PC board.

When you see this symbol on your instrument, you should refer to the instrument s instruction manual for important information. Used for menus, ewitch, dialog boxes, and button boxes on a computer monitor from attenuatr you make selections using the mouse or keyboard: If the original packaging materials are not available, you can contact an Agilent sales and service office to obtain information on packaging materials or you may use an alternative packing material referred to as bubble-pack.

Unpack and inspect the shipping container and its contents thoroughly to ensure that nothing was damaged during shipment. Agilent Technologies does not warrant that the operation of the instrument, or software, or firmware will be uninterrupted or error free. They must be ordered separately. With over 8, new and refurbished instruments in stock, as well as the best rates on rental equipment and trade-ins in the industry, Naptech is the first and last place you need to come for your test equipment needs.

  MOBILY USB MODEM DRIVER DOWNLOAD

Surround the module with at least 3 to 4 inches of its original packing material or bubble-pack to prevent it from moving in its shipping container. Amelia Merritt 5 attnuator ago Views: Agilent Technologies makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of attenator and fitness for a particular purpose.

However, Buyer shall pay all shipping charges, duties, and taxes for products returned to Agilent Technologies from another country. Mark the shipping container Fragile, Handle with Care to help ensure careful handling.

It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in damage to the product or loss of important data. The wrist-strap and wrist-strap cord are not included. agtenuator

HP – Agilent – Keysight A Attenuator, Switch Driver

Accessories Firmware Revisions Table To reliably install the pin connector to the ribbon cable use the following 3M tools. The instrument should be stored in a clean, dry environment. This means that at the default setting, seven groups of four switches and one group of three switches will each take 50 ms to switch and verify.

Switching speed is a function of pulse widths, sensing delays, the state of the chosen channels, the sequence of relays driven and the power supply recovery time.

  INTEGRATED HIGH DEFINITION AUDIO WITH REALTEK 4-CHANNEL ALC262 CODEC DRIVER DOWNLOAD

A power transistor on the driver board supplies the ground that will activate the switch coil. Figure Eight Driver Card Addresses It is impossible to predict the exact configuration of your particular switch matrix. If this product is to be powered by autotransformer, make sure the common terminal is connected to the neutral grounded side of the ac power supply.

All rights are reserved.

87130A Attenuator/Switch Driver. Operating and Service Guide

User Entry Used to indicate text that you will enter using the computer keyboard; text shown in this typeface must be typed exactly as printed: The power supply allows the switch driver four switching operations at the same time.

The duration of this warranty extends through January 31, The remedies available under this warranty will be defined in, and subject to, the terms and limitations of the warranties contained in the contract of sale.

Before connecting any coaxial cable to an instrument connector for the first time each day, momentarily ground the center and outer conductors of the cable. This results in a default switching speed of 0.

If this product atrenuator not used as specified, the protection provided by the equipment could be impaired. Using the Internal Driver 1. These low impedance pulses can be adjusted for pulse width in order to optimize switching speed.